The manufacturer dimensions of the shower pans are normally taken from flange to flange and the angles are omitted to be roughly what a square or rectangular measurement would be. I attached a picture that shows how the Better Bath Corner RV Shower Pan # LC298087 is measured at 27 by 27 inch. view full answer...
I checked with Ark and they informed me that their Drop Down Corner Stabilizer set part # AR34FR will work great on your 2015 Passport Grand Touring Ultra Lite but these jacks do not have a weight capacity. This is what they sent me:
"The # AR34FR is meant to only stabilize / steady the camper / caravan and is not meant to lift or hold its weight off the ground.
For this reason the DDS600 does not have a weight rating as it not mean to hold up any weight only steady/stabilize." view full answer...
The ideal clearance between the top of the bed rails on the truck and the bottom of the loft on the trailer is indeed around 6". This will allow for clearance between the truck and trailer during most normal driving encounters such as bumps in the road, steep driveways, etc. In regards to a specific angle, this, I cannot provide as there are several factors at play that would vary for each setup. The best advice I have would be to just use common sense when you are out and about. There's... view full answer...
The Replacement Water Valve for Dometic Pedal Flush RV Toilets # DOM93FR doesn't really have a warranty, but if you purchased the part and found a manufacturer defect with it right away Dometic would most likely replace it free of charge. If you purchased your RV from a dealership and had a warranty through them then you could most likely also get it replaced for free that way. view full answer...
Yes, the Adco RV Cover # AD27ZR will have side panels that are designed to protect your travel trailer from UV rays so it will work well for you in the Florida Sun.
You may also want to consider using the Camco RV Winter Readiness Kit # CAM36190 if you are storing your trailer for the winter months. Although Florida doesn't get hit as hard with the cold, it still is a wise option as temps can drop unexpectedly with weather changes. view full answer...
The speed rating for Kenda Karrier tire part # AM39053 is 81 MPH. That is the maximum speed recommended for these tires.
Most tires have a M, L or J on the sidewall of the tire that indicates the speed rating. This particular Kenda tire has a M rating. The letter M means 81 Mph, while L means 75 Mph and J means 62 Mph maximum speed. If the tire does not have a M, L or J on the sidewall, the default speed rating is 65. I have attached a helpful tire article for your reference. view full answer...
Hey Chris, the closest option to what you are looking for would be the Ventline Ceiling Garnish part # VA0445-28 which is birch white like you asked for and is basically exact same dimensions except is 1/8 of an inch taller. view full answer...
The observation camera that will work with your 2018 Keystone Passport GT is the Furrion RV Observation Camera System w/ Monitor and Bracket # FOS43TASF.
The Furrion Observation camera system has a camera that has a shaded design so glare in the bright sun won't be a problem, and also has infrared so you can use it without issue after the sun goes down. The camera is also waterproof so no matter the weather it will give you a durable, effective way to observe what is happening behind you.
The... view full answer...
I have a great underbed style fifth wheel hitch solution for your 2022 Ford F-250 Amanda but we don't have a way to install OEM style pucks in the bed of your truck. Instead I would recommend going with the B and W Companion hitch setup with the part # BWRVK3400 for the slider hitch and then part # BWGNRK1116 for the rail kit.
This gives you an underbed rail setup that that doubles as a gooseneck hitch which when not in use would give you a totally clean bed similar to the OEM pucks.... view full answer...
Hello Scott, so we have quite a few electric jacks that will be of sufficient capacity for your 2017 Keystone Passport Ultra Lite Grand Touring Travel Trailer. If you are looking for the fastest-moving jack, I recommend the Phoenix Electric Trailer Jack # UF38-944040. This has a 4,000 lb capacity and it will move 6" in about 10 seconds under 1,000 lbs of tongue weight. I imagine that with your camper being 7,500 lbs loaded, your tongue weight should be pretty close to 1,000 lbs so you should... view full answer...
An engine warmup delay is programmed into the remote start cycle. After the generator is running, there will be a delay of electrical output for 15 seconds. A delay also occurs after pushing STOP on the remote, so the electric load is automatically disconnected when using the remote.
This prevents the low voltage situation you mentioned. view full answer...
The Pro Series Weight Distribution System # 49570 you mentioned only has a maximum 2 inch drop with the shank that comes with the system. You most definitely need a longer shank for the height of your truck compared to your trailer coupler height. I recommend the Fastway e2 Weight Distribution Shank - 12" Long - 12-1/2" Rise 9-3/4" Drop - 1.2K TW # FA92-02-4315 which will give you the drop needed and will also accommodate the tongue weight of your system. You can alternatively use the... view full answer...
The Super Grip Chock XL Wheel Stabilizers for Tandem-Axle Trailers and RVs part # UF21-001095 will fit any trailer with tires spaced apart between 3-1/2" and 17" when measuring at the closest point. Therefore, the Super Grip Chock XL Wheel Stabilizers will be a good match for the Keystone Passport Ultra Lite. view full answer...
Since leaf springs tend to flatten out over time the original eye to eye measurement was probably closer to 25-1/4" or 25-1/8" so the 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles # e54SR would be an acceptable replacement. The shackle straps on the equalizer should allow you to make up the difference. Now would be a good time to also check your shackle straps and bolts for any damage and replace as needed. If you need help finding the correct replacements or want to switch to wet... view full answer...
What you read is correct. You have a 3,500 lb Lippert axle with an 85" hub face and a 68-1/2" spring center measurement. I do have a solution, but unfortunately we do not carry a standard axle with these measurements. What I can offer is the Timbren Axle-Less Trailer Suspension w Electric Brakes # A35RS545E. This system is universal so it fits any frame width. It would also replace your existing leaf springs and upgrade you to an independent suspension. view full answer...
We have removable motorcycle wheel chocks like the # RA-17 that will work great for you.
I attached a review video for the # RA-17 for you to check out as well. view full answer...
For a 3 inch hitch to 2 inch hitch adapter we have the part # 337RTA302. This will work great with your Fastway weight distribution system. view full answer...
Yes, you can use the MORryde CRE3000 on your 2014 Keystone Passport Ultra Grand Touring. You will need the # MR34AR which measure 14-3/4" since this is the closest match to your current 14-1/2" equalizers. The slight difference in length wont' be an issue.
I also recommend adding the MORryde Suspension Upgrade Kit for Tandem Axle Trailers while you're at it. The kit comes with wet bolts, bronze bushings, and 1/2" thick shackles. This simple upgrade gives you long lasting components so... view full answer...
The TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster - 4 Tire Sensors # TM89FR will alert you to the temperature of your tires but won't help with the actual overheating of your trailer bearings.
That is likely due to something internal within the hub such as the castle nut being over tightened, brake assemblies being over adjusted or a suspension issue such as a bent spindle. view full answer...
The first thing that stands out to me is that you used 12 gauge wire on a tandem axle setup when it's 10 gauge wire that is widely considered to be the minimum. I'd maybe try going up to 10 gauge wire like # 10-1-1 and you should see the issue go away as the wiring is probably just not able to handle the amperage needed.
The brake magnets can be wired in either configuration so the issue you mentioned would not be the problem either. But also check for any bare wire touching metal of the... view full answer...
Go To Results